PRODUCT DESCRIPTION
ISO-CONNECT INSIDE CX is a special water resistant and vapour diffusion impermeable foil for an air tight and wind proof sealant on connecting joints in
- windows
- doors
- panels
in accordance to the new energy saving regulation (EnEV) requirements. It consists of a water vapour diffusion permeable synthetic fleece with a self adhesive strip on one edge for a quick and effective application on window frames.
PRODUCT ADVANTAGES
- Fulfils the EnEV (energy saving regulations) requirements
- Airtight, wind proof and water vapour impermeable water resistant
- Water resistant
- Special fleece surface which is good for plastering, painting or pasting over
- With a self-adhesive strip for quick and effective installation
- Highly flexible, but with a high tensile strength for an easy and exact application
- 10 year performance guarantee*
*On the conditions of the manufacturer (available upon request).
Applications
ISO-CONNECT INSIDE CX is used to seal internal connecting joints. Due to its large sd-value it is suitable for sealing joints where an impermeable vapour diffusion, and airtight, seal is required, separating the internal and external air conditions.
ISO-CONNECT INSIDE CX is highly flexible, which aids exact application, particularly around corners. It also allows the optimum bonding of wet plaster, paint, etc. (without the need of a primer), and is extremely suitable as a base for thermal insulation materials applied to internal facades.
Service
- Standard sizes available from stock
- Private label and/or special labelling available
- Competent technical support available in the field and by phone
| Technical data | Standard | Classification |
| Material description | vapour diffusion impermeable synthetic fleece | |
| Colour | gray | |
| Weight | 250 – 300 g/m² | |
| Impermeable to driving rain | DIN EN 1027 | ≥ 1050 Pa |
| Air permeability coefficient | DIN EN 1026 | a ≤ 0,1 m³/[h*m*(daPa)ⁿ] |
| UV light stability | approximately 3 months | |
| Temperature stability range | internal | -40°C to +100°C |
| sd-value | DIN EN ISO 12572 | approximately 40 m |
| Flexibility at -23°C | internal | no breaks, no tears |
| Fire behaviour | DIN 13501 | E |
| Dimension tolerance | DIN 7715 T5 P3 | requirements fulfilled |
| Shelf life | 1 year, dry and in original packing | |
| Storage temperature | +1°C to +20°C |
Preparation
The bonding surfaces must be firm, dry, clean from dust, stripping agents, solvents, oil and grease. When sealing windows, panels and door frames remove backing from the self-adhesive strip, then lay the foil onto the surface and press securely. ISO-CONNECT INSIDE CX can be applied in the factory. For bonding to walls ISO-TOP FLEX-ADHESIVE SP or SP+ is used. Normal rough, e.g. uneven wall surfaces, can be compensated for through the application of a sufficent amount of adhesive. Use sufficient adhesive so that after applying the foil the adhesive caterpillar is at least 30 mm wide and 1 mm thick. On areas that are to be plastered over a continuous „Z“ shaped caterpillar should be applied over the area. Depending on the μ-values of the surface it can be necessary to increase the width of the adhesive caterpillar up to > 50 mm, in order to reduce the water vapour permeability. Overlapping of the foil ends should only be up to 50 mm wide using the same technique . Plastering over can be done as soon as the adhesive bond is enough to carry the weight of the plaster.
Finishes
Single side self-adhesive with 1 self-adhesive strip.
Special finishes available on request.
Dimensions
Width: 70, 90, 145, 180, 235, 290 mm.
Packaging
Rolls, roll length: 30 m.
Details and information presented in this document are based on the best knowledge available at the time. They are intended for general information purposes, and it is recommended that users conduct their own tests under their specific conditions to ensure the product’s suitability for its intended use. No definitive guarantee or liability can be given regarding the details or the absolute completeness of the information provided in these guidelines. We reserve the right to improve or modify technical specifications and information without prior notice.